基于试桩实测规律的大直径灌注桩荷载传递计算与分析

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (1529 KB) HTML ()
输出: BibTeX | EndNote (RIS)

摘要 This study aims to establish an appropriate method to calculate the bearing deformation of large-diameter bored piles in alluvial deposits with soils characterized mainly by medium-dense to dense silt, fine sand, and plastic to hard plastic silty clay in the middle and lower reaches of the Yellow River. According to the field measurement results of 18 large-diameter bored piles in six sites of the third-ring expressway project in Zhengzhou, this study discusses the action laws of pile shaft friction with pile-soil shear displacements and pile tip resistances with pile end displacements. A pile shaft load transfer model and pile tip bearing model are then established for large-diameter bored piles. The calculation parameter values are also given. The feasibility and rationality of the calculation method are verified by an engineering example. According to the engineering example and by changing the parameters of the pile diameter and pile length, the properties of bearing capacities and deformations of the large-diameter bored piles under this site condition are further analyzed. Results show that the inflection point of the pile Q~s curve is obvious for large pile diameters. The pile bearing capacity and deformation property are significantly improved by increasing the pile diameter under a small load. The increase amplitude of the pile bearing capacity and deformation property obviously decreases with the increase in pile length. This result indicates that the improvement of the pile bearing capacity and deformation property by increasing the pile length is not effective. The pile without grouting shows an obvious puncture damage model. Moreover, the settlement of the pile without grouting is small with a large pile diameter or short pile length. The effective length and bearing capacity of a large-diameter bored pile can be greatly increased by pile tip post grouting. The increased value of the pile bearing capacity is high with a large pile diameter and pile length under pile tip post grouting conditions.

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	李永辉
	朱翔
	陈陆杰
	周同和

关键词 ： bridge engineering, load transfer calculation, field measurement, large-diameter bored pile, pile shaft friction, pile tip resistance

Abstract：This study aims to establish an appropriate method to calculate the bearing deformation of large-diameter bored piles in alluvial deposits with soils characterized mainly by medium-dense to dense silt, fine sand, and plastic to hard plastic silty clay in the middle and lower reaches of the Yellow River. According to the field measurement results of 18 large-diameter bored piles in six sites of the third-ring expressway project in Zhengzhou, this study discusses the action laws of pile shaft friction with pile-soil shear displacements and pile tip resistances with pile end displacements. A pile shaft load transfer model and pile tip bearing model are then established for large-diameter bored piles. The calculation parameter values are also given. The feasibility and rationality of the calculation method are verified by an engineering example. According to the engineering example and by changing the parameters of the pile diameter and pile length, the properties of bearing capacities and deformations of the large-diameter bored piles under this site condition are further analyzed. Results show that the inflection point of the pile Q~s curve is obvious for large pile diameters. The pile bearing capacity and deformation property are significantly improved by increasing the pile diameter under a small load. The increase amplitude of the pile bearing capacity and deformation property obviously decreases with the increase in pile length. This result indicates that the improvement of the pile bearing capacity and deformation property by increasing the pile length is not effective. The pile without grouting shows an obvious puncture damage model. Moreover, the settlement of the pile without grouting is small with a large pile diameter or short pile length. The effective length and bearing capacity of a large-diameter bored pile can be greatly increased by pile tip post grouting. The increased value of the pile bearing capacity is high with a large pile diameter and pile length under pile tip post grouting conditions.

Key words： bridge engineering load transfer calculation field measurement large-diameter bored pile pile shaft friction pile tip resistance

收稿日期: 2017-07-24

基金资助:Supported by the National Natural Science Foundation of China (No.51508522)

通讯作者: LI Yong-hui E-mail: liyh109930@163.com

引用本文:

李永辉, 朱翔, 陈陆杰, 周同和. 基于试桩实测规律的大直径灌注桩荷载传递计算与分析[J]. Journal of Highway and Transportation Research and Development, 2018, 12(3): 28-36.
LI Yong-hui, ZHU Xiang, CHEN Lu-jie, ZHOU Tong-he. Load Transfer Calculation and Analysis of Large-diameter Bored Piles According to Rules Based on Test Pile Measurement. Journal of Highway and Transportation Research and Development, 2018, 12(3): 28-36.

链接本文:

http://manu27.magtech.com.cn/Jwk_gljtkj_en/CN/ 或 http://manu27.magtech.com.cn/Jwk_gljtkj_en/CN/Y2018/V12/I3/28

[1] GU Pei-ying, WANG De-ping, LU Hui-ming. Test Study on Side Friction of Large Diameter Bored Pile[J]. Journal of Highway and Transportation Research and Development, 2004, 21(1):62-66. (in Chinese)
[2] LIU Nian-wu, GONG Xiao-nan, YU Feng. Vertical Bearing Capacity of Large-diameter Bored Pile[J]. Journal of Zhejiang University:Engineering Science, 2015, 49(4):763-768. (in Chinese)
[3] WANG Xu, JIANG Dai-jun, LIU De-ren, et al. Experimental Study of Bearing Characteristics of Lager-diameter Cast-in-place Bored Pile Under Non-refreezing Condition in Low-temperature Permafrost Ground[J]. Chinese Journal of Rock Mechanics and Engineering, 2013, 32(9):1807-1812. (in Chinese)
[4] ZHANG Zhong-miao, HE Jing-yu, FANG Kai. Experimental Study on Size Effect of Large-diameter Bored Cast-in-situ Piles with Post-grouting in Soft Soil[J]. Chinese Journal of Geotechnical Engineering, 2011, 33(S2):32-37. (in Chinese)
[5] GUO Yuan-cheng, ZHANG Jing-wei, DONG Xiao-xing. Experimental Study on Bearing Capacity of Bored Piles Using Pile Tip and Side Post-grouting Technology[J]. Journal of Highway and Transportation Research and Development, 2014, 31(7):14-18. (in Chinese)
[6] WU Yi-zhang. Static Load Tests for Post-grouting Cast-in-situ Piles in Silt Region[J]. Building Science, 2013, 29(7):66-70. (in Chinese)
[7] FANG Kai, ZHANG Zhong-miao, LIU Zhi-jun, et al. Load Settlement Relationship Prediction for Grouted Pile Based on Load Transfer Function Method[J]. Journal of Harbin Institute of Technology, 2012, 44(12):95-99. (in Chinese)
[8] JIA Yu, SONG Fu-gui, WANG Bing-long, et al. Modified Load Transfer Method for Calculation of Foundation Pile Settlement Due to Dewatering[J]. Rock and Soil Mechanics, 2015, 36(1):68-74, 82. (in Chinese)
[9] CHEN Long-zhu, LIANG Guo-qian, ZHU Jin-ying, et al. Analytical Calculation of Axial Loading-settlement Curve of Piles[J]. Journal of Geotechnical Engineering, 1994, 16(6):30-38. (in Chinese)
[10] ZHANG Yi-jing,XIAO Hong-bi. Analysis on Bearing Capacity of Single Pile Based on Exponential Load Transfer Mode[J]. Building Structure, 2012, 42(7):119-122. (in Chinese)
[11] LIN Chun-jin, ZHANG Qian-qing, LIANG Fa-yun, et al. Analysis of Bearing Behavior of a Single Pile Considering Progressive Failure of Pile-soil System[J]. Rock and Soil Mechanics, 2014, 35(4):1131-1140. (in Chinese)
[12] WANG Xiang-jun. A Load Transfer Method for Analyzing Side-grouting Uplift Piles Based on Pile Tests[J]. Rock and Soil Mechanics, 2015, 36(S2):321-326. (in Chinese)
[13] WANG Wei-dong, LI Yong-hui, WU Jiang-bin. Pile-soil Interface Shear Model of Super Long Bored Pile and Its FEM Simulation[J]. Rock and Soil Mechanics, 2012, 33(12):3818-3825. (in Chinese)
[14] XIAO Hong-bin, ZHONG Hui-hong, ZHANG Yi-jing2, et al. Numerical Iteration Method for Determining Load-settlement Relationship of A Single Pile[J]. Rock and Soil Mechanics, 2002, 23(5):592-596. (in Chinese)
[15] LAI Qiong-hua. Calculation on Procedure for P-S Curve of Piles[J]. Chinese Journal of Rock Mechanics and Engineering, 2003, 22(3):509-513. (in Chinese)
[16] LI Yong-hui, WANG Wei-dong, HUANG Mao-song, et al. Experimental Study on Pile-soil Interface Shear Behaviors of Super-long Bored Pile[J]. Rock and Soil Mechanics, 2015, 36(7):1981-1988. (in Chinese)
[17] SAHARA M, AKINO N, TOMINGAGA K. Experimental Results and Elasto-plastic Analysis of the Vertical Behavior of a Single Model Pile[J]. Journal of Asian Architecture and Building Engineering, 2002,1(1):65-73.
[18] MULLINS G, WINTERS D, DAPP S. Predicting End Bearing Capacity of Post-Grouted Drilled Shaft in Cohesionless Soils[J]. Journal of Geotechnical and Geoenvironmental Engineering, 2006, 132(4):478-487.
[19] HIRAYAMA H. Load-settlement Analysis for Bored Piles Using Hyperbolic Transfer Functions. Soils and Foundations, 1990, 30(1):55-64.
[20] LI Yong-hui, WANG Wei-dong, WU Jiang-bin. Bearing Deformation of Large-diameter and Super-long Bored Piles Based on Pile Shaft Generalized Shear Model[J]. Chinese Journal of Geotechnical Engineering, 2015, 37(12):2157-2166. (in Chinese)